Customs tariff code 8501.32.00.65: Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless…
Reference data as at 1 July 2026
Customs tariff code 8501.32.00.65 covers Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor. The third-country duty rate is 2.7 %, plus import VAT.
8501.32.00.65 is TARIC code in the EU customs tariff, in chapter 85. This page shows the full classification path, the duty rate, the official comparison cases, and the notes that govern this code.
This code is not declarable on its own. A declaration needs one of the subdivisions beneath it.
- Customs code
- 8501.32.00.65
- Third-country duty
- 2.7 %
- Declarable
- No
- Binding rulings
- 3
Where this code sits in the tariff
- 85ELECTRICAL MACHINERY AND EQUIPMENT AND PARTS THEREOF; SOUND RECORDERS AND REPRODUCERS, TELEVISION IMAGE AND SOUND RECORDERS AND REPRODUCERS, AND PARTS AND ACCESSORIES OF SUCH ARTICLES
- 8501Electric motors and generators (excluding generating sets)
- 8501.32Of an output exceeding 750 W but not exceeding 75 kW
- 8501.32.00andere Gleichstrommotoren; Gleichstromgeneratoren, ausgenommen fotovoltaische Generatoren, mit einer Leistung von mehr als 750 W bis 75 kW
- 8501.32.00.65Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor
From HS code to customs tariff code 8501.32.00.65
Duty rates and preferences
| Origin | Duty rate | Basis |
|---|---|---|
| Third-country duty | 2.7 % | MFN |
| Switzerland | 0 % | Tariff preference |
| Faroe Islands | 0 % | Tariff preference |
| Melilla | 0 % | Tariff preference |
| Occupied palestinian Territory | 0 % | Tariff preference |
| Türkiye | 0 % | Customs Union Duty |
| San Marino | 0 % | Customs Union Duty |
| Andorra | 0 % | Customs Union Duty |
| EU-Switzerland agreement: re-imported goods | 0 % | Tariff preference |
| GSP-EBA (Special arrangement for the least-developed countries… | 0 % | Tariff preference |
| GSP+ (incentive arrangement for sustainable development and… | 0 % | Tariff preference |
| Moldova, Republic of | 0 % | Tariff preference |
| Ecuador | 0 % | Tariff preference |
Rates from the EU TARIC database. Preferential rates require valid proof of origin.
Compliance regimes on this code
Beyond the duty rate, these EU regimes attach to this code. Each verdict follows from the code alone; the goods themselves can still fall outside a regime.
Indicative correlation only. The mapping from customs codes to dual-use control codes is guidance, not a classification. Whether an item is controlled depends on its technical parameters.
- 8A002aMarine systems, equipment and components, as follows:
- 8A002jMarine systems, equipment and components, as follows:
- 8A002aMarine systems, equipment and components, as follows:
Derived from TARIC and the published EU regulations. It is a starting point for a screening, not a compliance assessment of your goods.
Binding tariff information for this code
"Elektromotor für Lenkungsunterstützung in Kraftfahrzeugen" - Bürstenloser, permanenterregter Gleichstrommotor, in unterschiedlichen Ausführungen - mit einer Drehzahl von jeweils 4000 U/min - mit den Leistungen von 797-896 W - für eine Spannung von 9,3 V, - Abmessungen: - - APA-Variante: Flanschdurchmesser: 91,8 mm, Gesamtlänge: 191,1-192,6 mm, Gehäuselänge: 147-148,5 mm - - DP-Variante: Flanschdurchmesser: 91,8 mm, Gesamtlänge: 130,7 mm, Gehäuselänge: 119,7 mm - in einem zylinderförmigen Aluminiumdruckgussgehäuse aus zwei Teilen (Grundgehäuse und Befestigung, sog. "Flansch") in verschiedenen Varianten mit zwei Befestigungsösen (DP-Variante) oder vier Schraubenführungen zur Befestigung (APA-Variante) - mit einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 12/8-Topologie und Oberflächenmagneten - zur Verwendung als Lenkungsunterstützung in Kraftfahrzeugen Derartige Waren gehören als "Elektromotor, keine Ware der Unterpositionen (HS) 8501 10 bis 8501 20, Gleichstrommotor, mit einer Leistung von 750 W oder weniger, nicht von den TARIC-Codenummern 8501 3100 10 bis 8501 3100 20 erfasst, für den Einbau in Kraftfahrzeuge geeigneter, bürstenloser, permanenterregter Gleichstrommotor mit einer spezifizierten Drehzahl von höchstens 4100 U/min, einer Leistung von mindestens 400 W, jedoch nicht mehr als 1,3 kW (bei 12 V), einem Flanschdurchmesser von 85 mm oder mehr, jedoch nicht mehr als 200 mm, einer maximalen Länge von nicht mehr als 335 mm, gemessen vom Anfang der Welle bis zu deren äußerem Ende, einer Gehäuselänge von nicht mehr als 265 mm, gemessen vom Flansch bis zum äußeren Ende, einem aus höchstens zwei Teilen (Grundgehäuse einschließlich elektrischer Komponenten und Flansch mit mindestens zwei, jedoch maximal 11 Bohrungen) bestehenden Stahlblech- oder Aluminiumdruckgussgehäuse, auch mit Dichtverbindung (Nut mit O-Ring und Schutzfett), einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 9/6 oder 12/8-Topologie und Oberflächenmagneten, auch mit elektronischem Steuergerät zur elektromechanischen Servolenkung, auch mit Riemenscheibe, auch mit Rotorpositionssensor" zum TARIC-Code 8501 3200 65.
Bürstenloser, permanenterregter Gleichstrommotor, sog. "Mehrphasen-Wechselstrommotor", - bestehend aus einem Elektromotor in einem zylinderförmigen Aluminiumdruckgussgehäuse aus zwei Teilen (Grundgehäuse und Befestigung, sog. "Flansch" mit neun Bohrungen) in APA-Variante mit Schraubenführungen zur Befestigung, - mit den Abmessungen: Flanschdurchmesser: 91,8 mm, Gesamtlänge: 204,1 mm und Gehäuselänge: 160 mm, - für eine Spannung von 9,3 V, - mit einer Leistung von 758 W, - mit einer Drehzahl von 4000 U/min, - mit einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 12/8-Topologie, - mit Oberflächenmagneten, - zur Verwendung als Lenkungsunterstützung in Kraftfahrzeugen. Die Ware ist als "Elektromotor, keine Ware der Unterpositionen (HS) 8501 10 bis 8501 20, Gleichstrommotor, mit einer Leistung von mehr als 750 W bis 75 kW, nicht für zivile Luftfahrzeuge, für den Einbau in Kraftfahrzeuge geeigneter, bürstenloser, permanenterregter Gleichstrommotor mit einer spezifizierten Drehzahl von höchstens 4100 U/min, einer Leistung von mindestens 750 W, jedoch nicht mehr als 1,55 kW (bei 36 V), einem Flanschdurchmesser von 85 mm oder mehr, jedoch nicht mehr als 200 mm, einer maximalen Länge von nicht mehr als 335 mm, gemessen vom Anfang der Welle bis zu deren äußerem Ende, einer Gehäuselänge von nicht mehr als 265 mm, gemessen vom Flansch bis zum äußeren Ende, einem aus höchstens zwei Teilen (Grundgehäuse einschließlich elektrischer Komponenten und Flansch mit mindestens zwei, jedoch maximal 11 Bohrungen) bestehenden Stahlblech- oder Aluminiumdruckgussgehäuse, auch mit Dichtverbindung (Nut mit O-Ring und Schutzfett), einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 9/6 oder 12/8-Topologie und Oberflächenmagneten, auch mit elektronischem Steuergerät zur elektromechanischen Servolenkung, auch mit Riemenscheibe, auch mit Rotorpositionssensor" einzureihen.
Bürstenloser, permanenterregter Gleichstrommotor, sog. "Mehrphasen-Wechselstrommotor", in unterschiedlichen Ausführungen, - bestehend aus einem Elektromotor in einem zylinderförmigen Aluminiumdruckgussgehäuse aus zwei Teilen (Grundgehäuse und Befestigung, sog. "Flansch") in verschiedenen Varianten mit zwei Befestigungsösen (DP-Variante) oder vier Schraubenführungen zur Befestigung (APA-Variante), - mit den Abmessungen: APA-Variante: Flanschdurchmesser: 91,8 mm, Gesamtlänge: 191,1-192,6 mm, Gehäuselänge: 147-148,5 mm, DP-Variante: Flanschdurchmesser: 91,8 mm, Gesamtlänge: 130,7 mm, Gehäuselänge: 119,7 mm, - für eine Spannung von 9,3 V, - mit den Leistungen von 797-896 W, - mit einer Drehzahl von jeweils 4000 U/min, - mit einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 12/8-Topologie, - mit Oberflächenmagneten, - zur Verwendung als Lenkungsunterstützung in Kraftfahrzeugen. Die Ware ist als "Elektromotor, keine Ware der Unterpositionen (HS) 8501 10 bis 8501 20, Gleichstrommotor, mit einer Leistung von mehr als 750 W bis 75 kW, nicht für zivile Luftfahrzeuge, für den Einbau in Kraftfahrzeuge geeigneter, bürstenloser, permanenterregter Gleichstrommotor mit einer spezifizierten Drehzahl von höchstens 4100 U/min, einer Leistung von mindestens 750 W, jedoch nicht mehr als 1,55 kW (bei 36 V), einem Flanschdurchmesser von 85 mm oder mehr, jedoch nicht mehr als 200 mm, einer maximalen Länge von nicht mehr als 335 mm, gemessen vom Anfang der Welle bis zu deren äußerem Ende, einer Gehäuselänge von nicht mehr als 265 mm, gemessen vom Flansch bis zum äußeren Ende, einem aus höchstens zwei Teilen (Grundgehäuse einschließlich elektrischer Komponenten und Flansch mit mindestens zwei, jedoch maximal 11 Bohrungen) bestehenden Stahlblech- oder Aluminiumdruckgussgehäuse, auch mit Dichtverbindung (Nut mit O-Ring und Schutzfett), einem Stator mit Einzel-T-Zahn-Design und Einzelspulenwicklung mit 9/6 oder 12/8-Topologie und Oberflächenmagneten, auch mit elektronischem Steuergerät zur elektromechanischen Servolenkung, auch mit Riemenscheibe, auch mit Rotorpositionssensor" einzureihen.
Notes that govern this classification
Erläuterungen zur Kombinierten Nomenklatur (KN) (entfallen) Hierher gehören z. B. Elektromotoren für Scheibenwischer, ohne Wischarm und Wischblatt, jedoch mit den für die Umwandlung der Drehbewegung in eine Pendelbewegung erforderlichen Kraftübertragungsvorrichtungen (Stirnradgetriebe und hin- und hergehende Stange).
Erläuterungen zum Harmonisierten System (HS) I) Elektromotoren Elektromotoren setzen elektrische Energie in mechanische Energie um. Zu dieser Gruppe gehören rotierende Motoren und lineare Motoren. A) Rotierende Elektromotoren erzeugen mechanische Energie in Form einer Drehbewegung. Es gibt zahlreiche Arten von rotierenden Elektromotoren, deren Merkmale voneinander abweichen, je nachdem, ob sie mit Gleichstrom oder Wechselstrom gespeist werden und je nach dem Verwendungszweck, für den sie gebaut sind. Bei manchen Motoren ist das Gehäuse der Umgebung, in der sie zu arbeiten haben, besonders angepasst, z. B. um sie gegen Staub und Feuchtigkeit zu schützen (so genannte gekapselte Motoren) oder auch um Brand- und Explosionsgefahr auszuschließen (Motoren mit schlagwettersicherem Gehäuse). …
Einzelentscheidungen zur Kombinierten Nomenklatur (EE) Durchführungsverordnung (EU) 2015/2255 der Kommission vom 02. Dezember 2015 (ABl. EU Nr. L 321/10) (RV L 15/2255) Eine Ware in Form eines flachen Zylinders (sogenannter „Mini-Vibrationsmotor“) mit einem Durchmesser von 9 mm und einer Höhe von 4 mm, mit eingebautem Gleichstrommotor, Spannung: 4 V, Leistung: 1 W. Die Ware ist für die Verwendung in Tablets, Mobiltelefonen usw. bestimmt, um einen Vibrationseffekt zu erzeugen. Dieser Effekt entsteht durch die Rotation eines asymmetrisch an den Motorschaft angebrachten Gewichts. Für den Einbau ist die Ware an einer Seite mit einem Klebeband versehen. (Siehe Abbildung) Unterposition 8479 89 97 Einreihung gemäß den Allgemeinen Vorschriften 1 und 6 für die Auslegung der Kombinierten Nomenklatur sowie nach dem Wortlaut der KN-Codes 8479, 8479 89 und 8479 89 97. …
Protokollerklärung des Ausschusses für den Zollkodex, Fachbereich Zolltarifliche und Statistische Nomenklatur (Teilbereich Textilien und Mechanik/Verschiedenes) - 278. Sitzung des Ausschusses für den Zollkodex vom 2. bis 4. März 2026: Warenbeschreibung: Das Spielzeug ist ein interaktives elektronisches Gerät, bestehend aus einer rechteckigen Kunststoffbox mit berührungsempfindlichem Bedienfeld, einem breiten, dünnen Plättchen mit Sensor (bewegliches Hologramm-Display), lichtemittierenden Dioden (LED), starken Neodym-Magneten, einer Magnetspule und 3 AA-Batterien. Neben diesen Komponenten sind keine weiteren Komponenten enthalten. Wenn die Box geöffnet wird, vibriert das Plättchen und es wird mit Hilfe der Dioden ein Bild einer Figur erzeugt und ein Ton abgespielt. …
Subdivisions of this code
Frequently asked questions
What does customs tariff code 8501.32.00.65 cover?
Code 8501.32.00.65 covers Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), - a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensor. Classification turns on the material, function, and intended use of the goods, not on their trade name.
What is the duty rate for 8501.32.00.65?
The third-country duty rate for 8501.32.00.65 is 2.7 %. Goods originating in a country with a preferential agreement may qualify for a lower rate against valid proof of origin.
What is the HS code for 8501.32.00.65?
The first six digits form the HS code: 850132. Those are uniform worldwide, while the further digits carry the EU Combined Nomenclature and the national subdivision.
How many digits does 8501.32.00.65 have?
8501.32.00.65 has ten digits and carries the EU measures held in TARIC. A German import declaration requires the eleven-digit commodity code.
Where does 8501.32.00.65 sit in the tariff?
8501.32.00.65 sits in this hierarchy: 85 ELECTRICAL MACHINERY AND EQUIPMENT AND PARTS THEREOF; SOUND RECORDERS AND REPRODUCERS, TELEVISION IMAGE AND SOUND RECORDERS AND REPRODUCERS, AND PARTS AND ACCESSORIES OF SUCH ARTICLES > 8501 Electric motors and generators (excluding generating sets) > 850132 Of an output exceeding 750 W but not exceeding 75 kW > 85013200 andere Gleichstrommotoren; Gleichstromgeneratoren, ausgenommen fotovoltaische Generatoren, mit einer Leistung von mehr als 750 W bis 75 kW. The parent headings and their notes help decide whether the classification holds.
Is there binding tariff information for 8501.32.00.65?
Yes. The EBTI database holds decisions on 8501.32.00.65, for example DEBTI4687/25-1. A BTI shows which product characteristics the customs authority relied on.
What happens if the customs tariff code is wrong?
An incorrect code leads to post-clearance recovery of duty and import VAT, delays at clearance, and a penalty where it repeats. A classification with documented reasoning can be defended in an audit.
Is 8501.32.00.65 a dual-use item?
The customs code alone does not decide that. An indicative correlation links 8501.32.00.65 to 8A002a, 8A002j, 8A002a. Whether your item is listed depends on its technical parameters and has to be checked against the wording of the control list.
Does customs tariff code 8501.32.00.65 change?
8501.32.00.65 is currently valid. The Combined Nomenclature is amended every 1 January, so master data should be checked against the current tariff annually.
Classifying more than one product?
This page shows one code. Zolltarif-Finder classifies entire product lists from Excel, CSV, or your ERP, with reasoning under GRI 1 to 6, official sources, compliance screening, and audit-ready reports.